PREWIRED HARNESS- Fender

Now your HSS Strat will finally sound the way it should. We have installed an Oak Grigsby super switch in this prewired Kit. This makes it possible to connect the pickups to the right potentiometers and capacitors, without the known disadvan ... (mehr lesen)

This is a blender prewired kit with treble bleed for the Stratocaster.   The standard 5 way strat circuit has a master volume and two tone pots. This circuit has a master volume, a master tone and a blender with which the neck and ... (mehr lesen)

This kit has a push/pull volume pot. The push/pull switch allows two more interesting positions in addition to the usual standard positions. If the volume button is pulled out, all three pickups are active in pos.4 (normally middle a ... (mehr lesen)

With the bridge tone control prewired kit it is possible to control the tone of all three pickups. With the usual standard circuit, the neck pickup is controlled with the first tone pickup, and the middle pickup with the second tone pickup. ... (mehr lesen)

This Prewired Kit fits into all HH-Strats with two splitable humbuckers. Some know the circuit from the Blacktop Strat. In position two and four both humbuckers are splitted, so that either the two inner or the two outer coils are active. ... (mehr lesen)

The 2x Capacitor Tone Control prewired Kit provides perfect tone control for the Strat with two capacitors. With the conventional standard circuit, only one capacitor is used for tone control, but this always means compromises. Depending on ... (mehr lesen)

This prewired kit corresponds to the 5-Way standard model, but is additionally equipped with a treble bleed mod. The treble bleed allows you to use the volume pot over the entire bandwidth without losing the treble.   Details: ... (mehr lesen)

This kit is the most versatile Stratocaster prewired kit in our range. We have a separate volume control for each pickup. This makes it possible to mix all 3 pickups together at will. For example, you turn the neck pickup up fully, the mid ... (mehr lesen)

The BROADCASTER / NOCASTER Prewired Kit corresponds to the circuit of the first Telecaster, at that time still Broadcaster from 1950- 52, and also the Double Esquire. The special thing about this circuit is that in position 1. the Neck picku ... (mehr lesen)

The circuit of this prewired harness corresponds to the 3-Way standard model from about 1967 until today, and is additionally equipped with a treble bleed mod. The treble bleed allows you to use the volume pot over the entire bandwidth witho ... (mehr lesen)

This Prewired Kit fits to Teles with splitable Neck Humbucker. Some may also know this circuit from the "U.S. Fat Tele". The kit has a special 5-way switch from Oak Grigsby which allows five different pickup combinations. Perfect for convert ... (mehr lesen)

With this circuit the single, parallel and serial switching of both pickups is possible. By connecting the two pickups in series, an additional fourth louder and fatter sound is created. For serial switching of the pickups, the neck pickup n ... (mehr lesen)

The circuit corresponds exactly to the model from 1953-65 with 2 capacitors. This circuit is known as "Dark Circuit", and should imitate an electric bass in pos.1, but was changed due to the drastic savings policy of CBS to the now known sta ... (mehr lesen)

If you want to mount the control plate of your Tele upside down, this kit is the right one for you. With the kit, the volume pot is mounted outside in the direction of the pickguard, and the tone pot in the middle. The switch is mounted on t ... (mehr lesen)

With this Reverse prewired Kit it is possible to switch the two pickups individually, in parallel and in series. By connecting the two pickups in series  a fourth additional louder and fatter sound is created. The Volume pot is arrang ... (mehr lesen)

The ESQUIRE prewired kit corresponds to the circuit with the three capacitors from 1950. This circuit was designed by Leo Fender so that the sound in pos. 1 resembles an electric bass (two .05 MFD capacitors in series), Pos. 2 is the usual t ... (mehr lesen)

Our Cocked Wah Esquire Prewired Kit is the best alternative to the original Esquire Wiring. In position one the pickup is directly looped through (true bypass), no volume, no tone pot is in the way. This gives you the full output with maximu ... (mehr lesen)

This Prewired Kit fits perfectly for the '72 Thinline Tele with the Wide Range Humbuckers (not suitable for the Single Coil Thinline). The Wiring is similar to the standard Thinline, and can also be equipped with a Treble Bleed Mod. The Treb ... (mehr lesen)

This circuit is similar to the one in the Custom Shop models with S1 Fender Switch and the two pickups. We use a much cheaper CTS push/pull pot instead of the expensive S1 switch, but the function is the same. When the push/pull is pulled, t ... (mehr lesen)

This Prewired Control Plate corresponds to the model from 1960 to 1962 with the original two stacked pots. With this circuit each pickup has its own volume and tone control. The kit is perfect for converting a standard bass to an early 60s ... (mehr lesen)

This kit corresponds to the model from 1960 to 1962 with the original two stacked pots. With this circuit each pickup has its own volume and tone control. The kit is perfect for converting a standard bass to an early 60s.   D ... (mehr lesen)

With this circuit it is possible to connect the two pickups in series and in parallel via a push/pull switch on the tone potentiometer. In the serial position (pull position) the sound gets louder and fatter.  Details: ... (mehr lesen)

In this Jazz Bass circuit we have a master volume, a master tone, and a balance pot in the middle, instead of the standard second volume. The balance pot allows the two pickups to be mixed together as desired. Once you've tried this wiring ... (mehr lesen)

The circuit corresponds to the standard model since 1963. Replacing the original wiring is also worthwhile with this kit, read below.    Details:     ARTY's WAXED PAPER SKIN Capacitor 50's Vintage Style ... (mehr lesen)

The circuit corresponds to the model from 1951-56 with control plate. Replacing the original wiring is also worthwhile with this kit, read below.   Before ordering, please make sure that the milling is wide enough for our ... (mehr lesen)

The circuit corresponds to the standard model since 1957. Replacing the original wiring is also worthwhile with this kit, read below.   Details:     ARTY's WAXED PAPER SKIN Capacitor 50's Vintage Style ... (mehr lesen)