PREWIRED KIT Gibson SG- Coil Split


SG Coil Split Prewired Kit with Bumble Bee Caps

The wiring of this Prewired Kit corresponds to that of the standard SG models. In addition we have installed two push/pull tone pots for independent splitting of the two humbuckers. Splitting the humbuckers creates the typical bright and crispy  single coil sound. This circuit adds real value to the standard configuration without push/pull potentiometers.
 

CAUTION:
The prewired kit works only in combination with splitable (3 or 4 wire) humbuckers. The CTS push/pull potentiometers that we use have a mounting height of 27,5 mm (including tooth lock washer). The potentiometers are may be too high for some SG style guitars. If in doubt, please measure the height of the electronics compartment before purchasing.

 

Details:

  •   2x CTS 500K Push/Pull 3/8" (9.52mm) Short Shaft Potentiometer, 3/8" thread
  •   2x CTS 500K 3/8" (9.52mm) Short Shaft Potentiometer, 3/8" thread
  •   ARTY's Bumblebee .022 uF and .015 uf Vintage Replica Capacitors
  •   SWITCHCRAFT Right Angle 3-Way Toggle Switch
  •   SWITCHCRAFT 1/4" Mono Audio Jack
  •   easy to understand Wiring Diagram

 

What's the difference between Gibson 50's vs. Modern Wiring?

50's Wiring

  •     when turning down the Volume more heights are remaining
  •     a turn of the Tone also affects the Volume
  •     with the Volume fully turned up there's a little more clarity and output

Modern Wiring

  •    better Volume control
  •    turning the Tone does not change the Volume
  •    significant loss of height when turning down the Volume (can be reduced with a Treble Bleed)

 

The shipping costs for most EU countries are € 12,-. You can find more information about shipping costs under the link directly below the product costs (inkl. Mwst., zzgl. Versandkosten). If your destination country is not listed here, please contact us to calculate the shipping costs.

 

If you need help with the checkout form or payment, please don't hestitate to contact us via e-mail. We just need your address and the designation of the desired items. As soon as we have received the above information, we will send you the detailed invoice.

 

132,00 €

  • auf Lager
  • Versand binnen 3-5 Werktage

Why a Prewired GUITAR WIRING HArness from Arty's Custom Guitars?

 

BECAUSE WE ARE ONLY SATISFIED WITH THE BEST.


All our prewired kits have matched pots and caps. This means that we measure all potentiometers and capacitors before installation, select them, and use them according to their values where they deliver the best possible result in combination with the pickups. This is important because original pots have tolerances of up to +-20%. In extreme cases, a 500k pot can have values of only 400k or up to 600k ohms. Not infrequently good pickups are replaced unnecessarily, because they sound muddy, weak or thin. In reality, however, the problem is often not due to bad pickups, but simply to inferior wiring, which mercilessly destroys the actually perfect sound.

We compared enormous quantities of capacitors in interaction with various pickups and thus determined the most suitable tone caps under real conditions. The capacitors are hand-selected HQ film capacitors with very low tolerance, very similar in design to the originals from the fifties. The vintage paper wax skin gives the caps an additional look. Our capacitors are so close to the originals of the 50's that nobody will hear a difference.

In all our kits only the best components from well-known manufacturers like CTS, Switchcraft, CRL or Oak Grigsby are used. All kits are carefully manufactured in small quantities and professionally handcrafted, and delivered to satisfied customers all over the world.

Wünsche, Fragen, Anregungen, ...

WIR FREUEN UNS AUF DEINE ANFRAGE!

 

Wishes, questions, suggestions,  ...

WE LOOK FORWARD TO YOUR REQUEST!